Short battery life with CR2032

[duhanebel]

Hi,
I've made 5 of these sensors v2 (great work btw! Thanks!!) without any extra sensor. That means I've only soldered:

• E18-MSI-PCB
• R1, R2, R3, R4
• LED1
• C1, C2
• D1
• SW1

Unfortunately I've now been running them for a few weeks and the battery voltage seems down between 2.2v and 2.8v. This is not consistent between different sensors.
What can be the reason for this? How can I find out what has gone wrong?

Also, reporting battery % varies wildly with time - see percentage vs actual voltage:

[quark72]

I have the same problem and discovered, that the module send not only one telegram/message. It send between 4 and 6 telegrams. And i see how in the first telegram the Voltage is 3.0V and in the last telegram it drops down.
I don't understood when and why how much telegrams are repeated - sometime it send 4, sometime 6, sometime 4. Only one time i received only one telegram.
The sending takes sometime a little bit over 1sec. Is it possible that this repeatedly sending of Data the Problem is?

[mattes34]

I also had the problem and built a firmware where only the soil moisture is measured. With this firmware I don't see jumps in the battery value since one day.

[duhanebel]

@mattes34 would you be able to send me an hex file with your version? I can't make IAR work for me no matter how much I tried :/

[mattes34]

Sure DIYRuZ_Flower_only_soilmoisture.zip
I think only with soil moisture measuring its possible to save energy by going back to only one cycle measurement like it was before Do only one wakeup cycle. If I fine time I will test it in the next days

Note: For reconnecting after flashing its seems that a factory reset is needed ? . I'm currently not sure how the connection is saved..

[smartboxchannel]

Try this special firmware for Versions 2 and 3 sensors running on cr2032

smartboxchannel/Plant-Watering-Sensor-Zigbee@53922d3

[duhanebel]

@smartboxchannel is that a drop in replacement for the v2 I've built? I've tried to flash it but the device keeps reporting NULL% moisture

[MatthijsThijssen]

Dear sender, I will be out of the office starting 9 June through 27 June returning. During this period i have limited access to my email. I will respond to your emails as soon as possible upon my return. You can also send your message to ***@***.*** so one of my colleague can follow up. Thank you for your message

[duhanebel]

@mattes34 I've tried with your firmware and while one device now works, other two refused to pair (3 LED blink every time). I'm not sure what I'm doing wrong. I've tried resetting the board by holding the button for 10seconds. On zigbee2mqtt I forced-removed the devices. My coordinator has only 10 devices connected so I don't think that is the problem (it wasn't before)
UPDATE: Never mind - my coordinator wasn't powerful enough and now it all works!

[Darozas]

@mattes34 I've tried with your firmware and while one device now works, other two refused to pair (3 LED blink every time). I'm not sure what I'm doing wrong. I've tried resetting the board by holding the button for 10seconds. On zigbee2mqtt I forced-removed the devices. My coordinator has only 10 devices connected so I don't think that is the problem (it wasn't before) UPDATE: Never mind - my coordinator wasn't powerful enough and now it all works!

Hi duhanebel , And how is battery life is with this firmware ? Regards

[mattes34]

Hi, I think the runtime was still not good. All my sensors run out after ~30days (2h reporting time). My new Idea is to set more focus on the measurement itself, becouse the start and stop of sampling is done in the event loop (static void zclApp_ReadSensors(void)) and maybe the measurement PWM is to long on. But I don't find time to work on it. To many projects.

mm maybe I find time to build a untested firmware, If you want to test it.

[Darozas]

Hi, I think the runtime was still not good. All my sensors run out after ~30days (2h reporting time). My new Idea is to set more focus on the measurement itself, becouse the start and stop of sampling is done in the event loop (static void zclApp_ReadSensors(void)) and maybe the measurement PWM is to long on. But I don't find time to work on it. To many projects.

mm maybe I find time to build a untested firmware, If you want to test it.

Yes sure i have 10of them and can test and record battery's on home assistant

[mattes34]

Hi, I make some changes (dirty and untested). good luck :D

https://github.com/mattes34/flower/blob/master/firmwares/DIYRuZ_Flower_soil_moisture_only.hex

[Darozas]

Hi, I make some changes (dirty and untested). good luck :D

https://github.com/mattes34/flower/blob/master/firmwares/DIYRuZ_Flower_soil_moisture_only.hex

Thanks Got it installed ill let you know results in few weeks!!!

[Darozas]

Hi, I make some changes (dirty and untested). good luck :D

https://github.com/mattes34/flower/blob/master/firmwares/DIYRuZ_Flower_soil_moisture_only.hex

Hi Would it be hard to implement BMP280 sensor?

[duhanebel]

I have a strange experience: out of 20 sensors, almost half have been running for 3+ months and have still a good amount of battery. The other half dies within weeks with brand new batteries. I wonder if it might have to do with my soldering? The components are all from the same batch.
I’ll try the new firmware anyway.. worth a try!